Home > Accessories >

Geek Vape 521 Tab
Geek Vape 521 Tab

Alternative Views:

Price: $15.95

Stock Status:(Out of Stock)
Availability:: Usually Ships in 24 to 48 Hours
Product Code: GEEKVAPE-521TAB

Description Extended Information

521 Tab by Geek Vape

The 521 Tab by Geek Vape is the end all for anyone that builds their own coils and uses rebuildable atomizers. The Geek Vape 521 Tab is more then a mere ohm reader. Using a single 18650 battery (Sold Separately) the Tab 521 can also fire the builds in your RDA's down to 0.1ohm.

Features & Specs :
  • Dimensions : 93.6mm x 75.4mm x 24.7mm
  • 510 Threaded
  • Ohm Reader
  • Resistance Reading Range : 0.01 - 9.9ohm
  • Can Fire Atomizers
  • Uses 1 x 18650 High Battery (Sold Separately)
  • Input Voltage : 2.7 - 4.2V
  • Output Voltage : 1.8 - 4.2V
  • Output Wattage : 31-33W
  • Minimum Firing Resistance : 0.1ohm
  • Three Position Switch : Off, Read, Fire (When in fire mode, press fire button with atomizer attached to fire coils.)
  • Low Voltage Protection
  • Short Circuit Protection
  • Breaker Protection
  • Reverse Polarity Protection
  • High Temperature Protection
Package Contents :
  • 1 x Geek Vape 521 Tab
Sold Individually

30 day limited warranty against manufacturer defects. Scratches and discoloration to the finish, normal wear & tear, accidental damage etc... is not covered by warranty.

***The use of Nickel Ni200 or Titanium Ti coils should only be used on devices equipped with circuit boards capable of temperature control. The use of these coils on any other device could result in an explosion.***

This device should only be used with Lithium Ion IMR Batteries with an amp limit of 20A and higher. Using any other battery can be potentially dangerous.
Use special caution when working with any Li-ion cells as they are very sensitive to charging characteristics and may explode or burn if mishandled. Make sure the end user is very knowledgable of Li-Ion rechargeable batteries in charging, discharging and assembly before use. Always charge in/on a fire-proof surface. Never leave charging batteries unattended.
We are not responsible for any damage caused by misuse or mishandling of Li-Ion batteries and chargers.
LiteCigUSA will not be held liable for any personal injury and/or damage temporary or permanent caused from the use of this product.

  0 of 0 people found the following review helpful:
5 of 5 January 5, 2018
Reviewer: Anonymous Person from Clarksville, TN United States  
I absolutely love this ohm reader by geekvape! My order was processed very quickly and shipped the next day. It arrived on time and upon opening I was extremely impressed with the build quality and would recommend this product to anyone looking to build their own coils. 10/10

Was this review helpful to you?

  0 of 0 people found the following review helpful:
5 of 5 Great product at a greater price July 6, 2017
Reviewer: Mike from Camarillo, CA United States  
I looked all over the internet for a better price and I couldn't find one. Lite Cig USA had the best price and they shipped it super fast!!!! Thumbs up!!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
4 of 5 Very handy February 3, 2017
Reviewer: Joe Smart from Illinois  
Works as advertised. My only complaint is no USB charging port but I can live without that.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
5 of 5 really nice November 19, 2016
Reviewer: Zachary Fulk from Newark, OH United States  
I love this thing ohms a little off. But not bad at all. Made a SS coil it read .20 put it in my tank and my subbox mini reads .18.. and love that you can test fire and make sure your coils fire up right. Then vape off it before you put it on your mod

Was this review helpful to you?

  0 of 0 people found the following review helpful:
3 of 5 Less useful than anticipated. June 13, 2016
Reviewer: Anonymous Person  
I was hoping for a tool to assist with my coil builds that was better/faster/cheaper than just using a mod. It really isn't.

It's a more stable base to work with if you're using it to hold your deck while assembling the coils, but it doesn't do anything that a regulated mod wouldn't do for you.

Also, and I'm surprised that this bothered me, the glossy finish attracts fingerprints like crazy and really holds onto them. If you want to clean it up, you really have to work at it.

I'll continue to use it for coil builds, but I wouldn't have bought it if I knew then what I know now.

YMMV, of course.

Was this review helpful to you?

View All Customer Reviews

Browse for more products in the same category as this item:

Accessories > Misc Accessories
Accessories > Rebuildable Supplies
Mods & RDA's > Rebuildable Atomizers
Mods & RDA's > Box Mods